JS29F01T2ALCQK1
Intel · 128GB QLC · BGA132
Chip Specifications
Structured Data- Brand
- Intel
- Capacity
- 128GB
- Flash Cell
- QLC
- Process
- N38A
- Flash Type
- NAND
- Package
- BGA132
- Voltage
- 1.8V/1.2V
- Operating Mode
- Toggle
- Die Count
- 0
- CE Count
- 1
89D3AC32C600Flash ID Identification
A Flash ID is an important identifier, but it cannot prove full compatibility by itself. Vendors may reuse some bytes across capacities, processes, or packages, and MP tools may display the bytes in a different order.
Verify in this order:
- Read the ID on the original PCB and record the value returned by every channel and CE.
- Compare the part number, capacity, brand, and package to eliminate obvious mismatches.
- Match the complete ID in the MP tool database, not only the first two bytes.
- Verify geometry parameters such as Page, Block, Plane, LUN, and ECC.
- Confirm stability with a limited read/write test before a full-device production run.
Benchmark Records
Associated public benchmark records: 5. Sequential read averages 22.6 MB/s and peaks at 31.1 MB/s; sequential write averages 21.5 MB/s and peaks at 25.5 MB/s.
| Test Controller | Flash Count | Sequential Speed | Random Speed | Operating System | Notes |
|---|---|---|---|---|---|
| FC1179 | 1 | R:9.81MB/s, W:18.1MB/s | R:6.41MB/s, W:0.54MB/s | Windows7 | 刚开始读写速度跑满2.0接口速度 之后开始降速 |
| FC1179 | 1 | R:22.15MB/s, W:19.11MB/s | R:0MB/s, W:0MB/s | Windows7 | 重新开卡为32gb 读写速度在写入四分之三时下降至15mb/s左右 |
| Other | 1 | R:19.5MB/s, W:24.5MB/s | R:0MB/s, W:0MB/s | Windows11 | FC2279 重开卡成pSLC 读取一条直线 写入前200M和后200M降速 |
| Other | 1 | R:30.55MB/s, W:25.48MB/s | R:0MB/s, W:0MB/s | Windows11 | ECC2降容至2GB FC2279 |
| Other | 1 | R:31.08MB/s, W:20.08MB/s | R:0MB/s, W:0MB/s | Windows11 | FC2279强制半容ECC0开卡4.5GB |
Speeds apply only to the tested controller, PCB, firmware, interface bridge, capacity, and environment. USB bridges, SLC cache, free-space state, temperature, and benchmark software can materially change the result; these figures are not absolute Flash performance specifications.
Mass Production and Repair Troubleshooting
Before Mass Production
- Determine whether data recovery is required; mass production and low-level formatting usually destroy the original data.
- Photograph both sides of the PCB, all chip markings, and jumper states.
- Record the full controller marking, oscillator, Flash count, and CE count per chip.
- Back up the ROM, ISP data, configuration files, and tool logs.
- Use a current-limited power supply to check for shorts and abnormal heating.
When the Device Is Not Detected
- Check VCC/VCCQ, reset, and clock signals.
- Check for weak BGA joints, lifted pads, and broken channel traces.
- Read IDs by channel and CE to isolate a faulty chip.
- Try the matching MP tool version or Flash database.
- Confirm that the firmware supports the process and ECC requirements.
- If uncertainty remains, stop writing and preserve the original state.
Technical Documents and Standards
- Search for the official JS29F01T2ALCQK1 datasheet: prefer the chip vendor’s website and the original PDF, and verify the document revision.
- Official ONFI 6.0 Specification：NAND interfaces, commands, parameter pages, and high-speed timing.
- Official ONFI 5.1 Specification：Covers SDR, NV-DDR, NV-DDR2, NV-DDR3, and related interfaces.
- JEDEC Standards and Document Search：Search standards for packages, electrical characteristics, SSDs, UFS, eMMC, and related technologies.
In the manufacturer datasheet, verify the ordering part number, package code, pins, absolute maximum ratings, operating voltage, interface timing, memory organization, bad-block management, ECC, endurance, and data retention. If search results conflict with this page, rely on the correct datasheet revision and physical measurements.
Data Reliability Notice
This page is compiled from public structured data and user benchmark records; it is not an official Intel datasheet. Hardware details can vary by batch, firmware, or tool identification method. Cross-check multiple sources for data recovery, production use, or high-value devices.